好的军事模型制作完成后逼真，可供人观赏，也可用于军事教学。那么
大型军事模型的制作有什么步骤呢？有工具的可以一起来做哟！
Good military models are lifelike and can be used for people's enjoyment and military teaching. So what are the steps involved in making a large military model? Those who have the tools can do it together!
工具
tool
模型一套、模型胶水（田宫和小号手ABS胶水）、笔刀、水口剪钳、直弯镊子两支、九洋切割板、打磨条、砂纸一套锉刀一套、模型手锯、模型手钻（钻头有0.022mm的钻头）、模型开模器、打磨块、牙膏补土、模型AB补土、水补土。如果模型设计不合理想要改进或者增加金属细节我们可以用到PE（铜制蚀刻片）ABS塑料胶板、铜线。上色工具有面相笔、平头画笔和喷笔喷泵、遮盖带。旧化装备有旧化土、渍洗液，也可用丙烯颜料加打火机油做渍洗。
Model a, model glue (tamiya and trumpeter ABS glue), pen knife, shuikou pliers, straight curved tweezers two, article 9 the cutting board, grinding, abrasive paper, a set of file a model, model handsaw, hand drill (0.02 to 2 mm drill bit has), model open mode, putty grinding block, toothpaste, water model AB putty, putty. If the model design is not ideal to improve or increase the metal details we can use PE (copper etching sheet) ABS plastic plate, copper wire. Coloring tools are face pen, flat brush and spray pen spray pump, cover belt. Old equipment has old soil, stain lotion, can also be used propylene pigment and lighter oil to do stain washing.
方法
methods
我们说组装，按照说明书的编号指示，找到相应编号的零件板件，按照英文字母的数字编号，使用水口剪钳剪下零件将水口用笔刀削整，砂纸打磨平整后，涂上模型胶水，与另一个零件相粘，并用手压紧十秒钟左右就可以了，两个零件之间对合留一条小缝，用绿盖胶水刷上一点即可胶水顺着缝隙流满后用手压紧使胶水溢出，待完全干后用砂纸打磨平整即可，此方法不是一次就行需要多次点胶，如果零件契合不好溜缝胶水无法弥补住缝隙时我们就要用到牙膏补土了，将牙膏补土挤出涂在缝隙上，使用一次性探牙针或笔刀进行填缝，待干后使用砂纸打磨平整即可。
First we say assembly, the number of instructions, in accordance with the specification to find the corresponding number of parts, the panel is according to the number of English letters number, use the shuikou pliers to shuikou pen knife cut the whole cut parts, sand paper after grinding smooth, glue coating model, and the other parts are glued, pressure for more than ten seconds with the hand, involution leave a small crack between the two parts, With green cover brush a little glue can glue along the gap flow pressure make the glue overflow with the hand, after the expiration of the stay dry sanding formation can be used after completely, this method is not just a need glue for many times, if the bad parts fit slip joint glue cannot make up for live gap when we're going to use toothpaste putty, putty squeeze toothpaste besmear is on gap, Use disposable probing needle or pen knife to fill the gap, and use sandpaper to smooth it after drying.
上色
coloring
上色是模型三步走的（组装上色旧化）第二步，我们要知道，上色是手绘还是喷泵喷涂，无论手绘还是喷涂在上色之前都需打上一遍水补土，水补土可以视为底漆，也可视为模型更后的补縫剂，上色时也可以似的模型漆的附着能力更好，也可以判断模型的迷彩涂装是否均匀，使用之前上下摇晃均匀。
Color is the model of the three steps of paint (assembly) old second step, the first thing we want to know, color is hand-drawn or spray pump spray, hand-drawn or spray before coloring are required to play in the water again fill soil, water putty can be regarded as primer, model also can be regarded as the final fill seam an agent, color also can model paint adhesion ability is better, You can also judge whether the camouflage coating of the model is even. Shake it up and down before using it.
上色后注意事项
Note after coloring
手钻是为模型定位孔打孔用的，很多老式模型零件定位孔，没有全部打开，需要玩家自己开孔，这时我们就用到了手钻，手钻在改造塑料履带可动方面也是要用的。使用笔刀修整零件时一定要注意防止割伤自己或刀片崩裂造成伤害。模型制作一般不适用14岁以下人群，适合成人或14岁以上玩家。模型不是玩具不适合把玩。
The hand drill is used to drill the positioning holes of the model. Many positioning holes of the old model parts are not all opened, and the player needs to open them by himself. At this time, we use the hand drill. When using a pen knife to repair parts, pay attention to safety to avoid cutting yourself or blade breakage. Model making is generally not suitable for people under 14 years old, suitable for adults or players over 14 years old. Models are not toys to play with.
The model brand on the market is multifarious, so on the choice needs to pay more attention to is, more content will come to our website to see!
