1.  很简单，直接掰下来就是。

It's very simple. Just break it off.

这里要说的关键就是：千万不要画蛇添足去企图整修已经被胶水溶化变形的部分。

The key here is: don't try to repair the part that has been melted and deformed by glue.

这样有可能适得其反，造成越修变形越厉害。  其实只要把已经分开的部件丢一边就可以了(如底图的样子)。等待1天左右胶水完全固化以后，再进行多余部分的切除和变形部分的整修工作。这样做的效果比较好。

This may backfire, resulting in more severe deformation. In fact, just throw away the separated parts (as shown in the bottom picture). Wait for about 1 day after the glue is completely solidified, and then carry out the removal of the surplus part and the renovation of the deformed part. The effect of this is better.

2．切除／掰除

2. Cutting / breaking off

如果胶水已经固化，那直接掰除会有一定的风险，可能造成零件的变形乃于破损。这种情况，好能用笔刀先沿着零件粘合部位切出一道缝来，然后慢慢掰。  这时候要时刻注意零件的变形情况，一旦出现零件变形的征兆，必须立刻停止，换用以下的法子  3．冷冻法

If the glue has solidified, there will be a certain risk of breaking off directly, which may cause deformation or even damage of parts. In this case, it is best to use a penknife to cut a seam along the bonding part of the part, and then break it slowly. At this time, we should always pay attention to the deformation of the parts. Once there is a sign of deformation of the parts, we must stop immediately and use the following ultimate method. 3. Freezing method

有时已经粘结的模型零件并不具备切除／掰除的条件，或者很难用力，那么，我们将不得不借助我们在中学时候学过的一个物理原理“热胀冷缩”来帮助我们这个问题。

Sometimes the bonded model parts do not have the conditions of cutting / breaking off, or it is difficult to use force. Then, we will have to help us solve this problem with the help of a physical principle we learned in middle school, "thermal expansion and cold contraction".

水煮开冷却到50-70度【注意零件厚度控制水温，别整变形了】放进去等热了 丢冰箱速冻室。胶水粘合处自然会崩开  。

Boil the water and cool it to 50-70 ℃ [pay attention to the thickness of the parts, control the water temperature, don't deform] put it into the freezer and throw it into the quick freezing room. The glue will crack naturally.

将模型丢进冰箱的速冻室里冻上几个小时，由于热胀冷缩的原因，造成了零件之间的微小裂缝，而这个裂缝往往出现在零件之间的连接处。那么，这正是我们将它们掰下来的好机会。

The model is put into the quick freezing room of the refrigerator for several hours. Due to the thermal expansion and cold contraction, there are tiny cracks between the parts, which often appear at the joints between the parts. So, this is a good opportunity for us to break them off.

4．如果连“冷冻法”都不奏效怎么办？

4. What if the freezing method doesn't work?

，基本上百分之九十九的零件都可以用“冷冻法”掰来下来，如果连这都不行，只能指望掰下来再修复了。

First of all, basically 99% of the parts can be broken off by "freezing method". If this is not possible, we can only hope to break them down and repair them.